Where Is The Serial Number For Jetson Electric Element Scooter?

How do you reset a Jetson scooter?

How do I reset my Jetson Tempo Scooter?

  1. Place the Tempo on a flat, level surface and turn power off for about 5 minutes.
  2. Press the Reset Button in.
  3. Restart the Tempo by turning it off and then on.

How do I connect to my Jetson?

Open the Ride Jetson app in your device, and locate the Bluetooth icon in the top left corner. 4. Tap on the Bluetooth icon, and from the device list, select your Jetson Beam.

Where is the serial number on a hover board?

The serial number is printed on a white sticker on the bottom of the deck or on the charger. Remedy: Consumers should immediately stop using these recalled products and contact Razor to return their hoverboard for a free replacement hoverboard that is certified to comply with UL 2272.

How do you start a Jetson electric scooter?

To start your Glow scooter, ensure that the power switch is turned on and the deck lights illuminate. Next, kick start your scooter using one foot to push scooter forward for about 5-8 kicks to before clicking the throttle. Note: Motor will only engage if scooter wheels are moving at 3-4mph.

You might be interested:  FAQ: How Far Can You Travel On An Electric Scooter?

How do I reset my electric scooter?

Problem 3: How Do I Reset My Electric Scooter?

  1. Place your electric scooter on a level, flat surface.
  2. Turn off the scooter and wait for about 5 minutes.
  3. Press the ‘ reset ‘ button to switch it on again.
  4. Now, the power switch should get illuminated, and it should work smoothly.

Why is my electric scooter not working?

Check the battery and charger. If the electric scooter does not run check the motor because the motor is the power source. Because of excessive riding or doing stunts may cause the problems. If the indicator does not work properly change the charger and then try again.

Does the Jetson Bolt Pro connect to the app?

At this time, our Bolt Pro bike does not have Bluetooth or Ride Jetson App capabilities.

How do you connect the Jetson bolt to the app?

First power on your Bolt and open the Ride Jetson app on your handheld device. Once in the app, click the Bluetooth symbol in the top left corner of the app and select your Bolt. The default Bluetooth password is 000 000.

How do I change the mode on my Jetson hoverboard?


  1. Place the Strike on its side.
  2. Power the Strike on—the indicator light will illuminate red for advanced (fast) mode.
  3. Quickly press and release the power button to cycle through the speed modes. Stop once the indicator light changes to the respective color of your desired speed.

Do Hoverboards have serial numbers?

M3A3) Hovertrax brand hoverboards have serial numbers beginning with 55X120-01, 55X120-02, 55X110-01, 55X110-02 and 55X230-01.

You might be interested:  Quick Answer: How Are The Charger For Electric Scooter Connected?

Do razor Hoverboards explode?

Razor is one of the first companies to obtain the UL 2272 certification for its products. This means if you’re using the Hovertrax 2.0, there is no fear of explosion during charging or during use of the hoverboard. It is also advisable to avoid a wet environment when using your hoverboard.

What Hoverboards are being recalled?

Seven hoverboard brands recalled over fire risk

  • Smart Balance Wheel Self-Balancing Scooters/ Hoverboards.
  • Drone Nerds Self-Balancing Scooters/ Hoverboards.
  • Go Wheels Self-Balancing Scooters/ Hoverboards.
  • iHoverspeed Self-Balancing Scooters/ Hoverboards.
  • iLive Self-Balancing Scooters/ Hoverboards.

How do you unlock a Jetson scooter?

All you’ve got to do is lift the handlebar away from the deck. Next, you lift the release lever until you hear a click. This means that your handlebar is now locked, and your Element scooter is ready to take you to your destination.

How do you charge a Jetson electric scooter?

To charge your Glow scooter, simply plug the charger into a working wall outlet. Next, plug the charger into the charging port located on the bottom, left of the scooter’s deck. When charging, the indicator light on the charger will display red and turn to green/blue when fully charged (no longer than 4 hours).

Related posts

Leave a Comment